 |
SIMATIC DP, ELECTRONIC MODULE ANALOG, FOR ET 200B, W=160MM, 4AO 0(4)...20MA; /- 10V, 11 BIT, 12 MBIT/S |
| Supply voltage |
| permissible range, lower limit (DC) |
18.5 V |
| permissible range, upper limit (DC) |
30.2 V |
| Load voltage 1L |
| ● Rated value (DC) |
24 V; Value at t < 0.5 s: 35 V |
| Input current |
| from supply voltage L , max. |
200 mA; Logic |
| Power losses |
| Power loss, typ. |
2.4 W |
| Hardware configuration |
| Rack |
| ● Required terminal block |
TB8 |
| Analog outputs |
| Number of analog outputs |
4 |
| Voltage output, short-circuit protection |
Yes; Electronic; max. 1 output in parallel |
| Voltage output, short-circuit current, max. |
25 mA |
| Current output, no-load voltage, max. |
18 V |
| Output ranges, voltage |
| ● 0 to 10 V |
Yes |
| ● -10 to 10 V |
Yes |
| Output ranges, current |
| ● 0 to 20 mA |
Yes |
| ● 4 to 20 mA |
Yes |
| Connection of actuators |
| ● for voltage output two-wire connection |
Yes |
| ● for voltage output four-wire connection |
Yes |
| ● for current output two-wire connection |
Yes |
| Load impedance (in rated range of output) |
| ● with current outputs, max. |
300 Ω |
| ● with current outputs, inductive load, max. |
1 mH |
| Cable length |
| ● Cable length, shielded, max. |
100 m |
| Analog value creation |
| Integration and conversion time/resolution per channel |
| ● Resolution with overrange (bit including sign), max. |
11 bit; Two''s complement |
| ● Conversion time (per channel) |
1 ms |
| Settling time |
| ● for resistive load |
0.1 ms |
| ● for capacitive load |
3.3 ms |
| ● for inductive load |
0.5 ms |
| Errors/accuracies |
| Output ripple (based on output area, bandwidth 0 to 50 kHz), ( /-) |
0.05 % |
| Linearity error (relative to output range), ( /-) |
0.05 % |
| Temperature error (relative to output range), ( /-) |
0.02 %/K |
| Crosstalk between the outputs, min. |
40 dB |
| Repeat accuracy in steady state at 25 °C (relative to output area), ( /-) |
0.05 % |
| Operational limit in overall temperature range |
| ● Voltage, relative to output area, ( /-) |
0.05 % |
| ● Current, relative to output area, ( /-) |
1 % |
| Basic error limit (operational limit at 25 °C) |
| ● Voltage, relative to output area, ( /-) |
0.2 % |
| ● Current, relative to output area, ( /-) |
0.3 % |
| Interfaces |
| PROFIBUS DP |
| ● Transmission rate, max. |
12 Mbit/s |
| Communication functions |
| Bus protocol/transmission protocol |
PROFIBUS DP |
| Interrupts/diagnostics/status information |
| Alarms |
| ● Diagnostic alarm |
Yes; Parameterizable |
| Diagnostics indication LED |
| ● Bus fault BF (red) |
Yes |
| ● Run mode RUN (green) |
Yes |
| Galvanic isolation |
| between electronic block and PROFIBUS DP |
Yes |
| Galvanic isolation analog outputs |
| ● Galvanic isolation analog outputs |
No |
| Degree and class of protection |
| IP20 |
Yes |
| Ambient conditions |
| Operating temperature |
| ● horizontal installation, min. |
0 °C |
| ● horizontal installation, max. |
60 °C; 40°C for other mountings |
| Air pressure |
| ● permissible range, min. |
795 hPa |
| ● permissible range, max. |
1 080 hPa |
| Relative humidity |
| ● Operation, min. |
15 % |
| ● Operation, max. |
95 %; RH class 2 in accordance with IEC 1131-2 |
| Vibrations |
| ● Operation, checked according to IEC 60068-2-6 |
Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g) |
| Shock test |
| ● checked according to IEC 60068-2-27 |
Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms |
| Connection method |
| Inputs/outputs |
Screw-type and spring-loaded terminals, permanent wiring; 3 and 4-wire connection |
| Dimensions |
| Width |
160 mm; EB and TB |
| Height |
130 mm; EB and TB |
| Depth |
60 mm; EB and TB |
| Weights |
| Weight, approx. |
550 g; EB and TB |
| last modified: |
08.09.2014 |
