 |
SIMATIC DP, ELECTRONIC MODULE 2 AO HIGH FEATURE I FOR ET 200S, 15 MM WIDE, /-20MA, 15 BIT SIGN, 4 .. 20MA, 15 BIT, OPERATIONAL LIMITS /-0.07% WITH LED SF (GROUP FAULT) |
| Supply voltage |
| Load voltage L |
| ● Rated value (DC) |
24 V; From power module |
| ● Reverse polarity protection |
Yes |
| Input current |
| from load voltage L (without load), max. |
150 mA |
| from backplane bus 3.3 V DC, max. |
10 mA |
| Power losses |
| Power loss, max. |
2 W |
| Address area |
| Address space per module |
| ● Address space per module, max. |
4 byte |
| Analog outputs |
| Number of analog outputs |
2 |
| Current output, no-load voltage, max. |
18 V |
| Cycle time (all channels) max. |
1.5 ms |
| Output ranges, current |
| ● -20 to 20 mA |
Yes |
| ● 4 to 20 mA |
Yes |
| Connection of actuators |
| ● for current output two-wire connection |
Yes |
| ● for current output four-wire connection |
No |
| Load impedance (in rated range of output) |
| ● with current outputs, max. |
500 Ω |
| ● with current outputs, inductive load, max. |
1 mH |
| Destruction limits against externally applied voltages and currents |
| ● Voltages at the outputs towards MANA |
15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20) |
| ● Current, max. |
50 mA; DC |
| Cable length |
| ● Cable length, shielded, max. |
200 m |
| Analog value creation |
| Integration and conversion time/resolution per channel |
| ● Resolution with overrange (bit including sign), max. |
16 bit; /-20 mA: 16 bits, 4 to 20 mA: 15 bits |
| ● Basic conversion time, ms |
1,0 |
| Settling time |
| ● for resistive load |
0.25 ms |
| ● for capacitive load |
1 ms |
| ● for inductive load |
0.5 ms |
| Errors/accuracies |
| Output ripple (based on output area, bandwidth 0 to 50 kHz), ( /-) |
0.02 % |
| Linearity error (relative to output range), ( /-) |
0.02 % |
| Temperature error (relative to output range), ( /-) |
0.001 %/K |
| Crosstalk between the outputs, min. |
60 dB |
| Repeat accuracy in steady state at 25 °C (relative to output area), ( /-) |
0.01 % |
| Operational limit in overall temperature range |
| ● Current, relative to output area, ( /-) |
0.07 %; for 250-ohm load impedance; /-0.3% for all other load impedances |
| Basic error limit (operational limit at 25 °C) |
| ● Current, relative to output area, ( /-) |
0.03 %; for 250-ohm load impedance; /-0.26% for all other load impedances |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) |
Yes |
| Interrupts/diagnostics/status information |
| Substitute values connectable |
Yes; Parameterizable; 0 to 65535 (value range must be within rated range) |
| Diagnostic messages |
| ● Diagnostic information readable |
Yes |
| ● Wire break |
Yes |
| ● Group error |
Yes |
| Diagnostics indication LED |
| ● Group error SF (red) |
Yes |
| Parameter |
| Remark |
7 byte |
| Output type/range |
deactivated / /-20 mA / 4 to 20 mA |
| Diagnosis: wire break |
Disable / enable |
| Group diagnostics |
Disable / enable |
| Behavior on CPU/Master STOP |
Output current and de-energized/substitute a value/keep last value |
| Galvanic isolation |
| Galvanic isolation analog outputs |
| ● between the channels |
No |
| ● between the channels and the backplane bus |
Yes |
| ● between the channels and the load voltage L |
Yes |
| Permissible potential difference |
| between MANA and M internally (UISO) |
75 VDC / 60 VAC |
| Isolation |
| Isolation checked with |
500 V DC |
| Dimensions |
| Width |
15 mm |
| Height |
81 mm |
| Depth |
52 mm |
| Weights |
| Weight, approx. |
40 g |
| last modified: |
25.09.2014 |
