- |
SIMATIC DP, ELECTRONIC BLOCK FOR ET 200L, 16 DO, 24V DC/0.5A |
|
| General information |
| Vendor identification (VendorID) |
0016h |
| Supply voltage |
| 24 V DC |
Yes |
| Reverse polarity protection |
Yes |
| Mains buffering |
| Mains buffering, min. |
20 ms |
| Load voltage 2L |
| Rated value (DC) |
24 V; 1L , 2L , 3L |
| Input current |
| from load voltage L1 (without load), max. |
50 mA; Per load group (L1 or L2 / L3 ) |
| Hardware configuration |
| Rack |
| Required terminal block |
TB 16L |
| Digital outputs |
| Number of digital outputs |
16 |
| short-circuit protection |
Yes |
| Response threshold, typ. |
0,7 A |
| Limitation of inductive shutdown voltage to |
Typ. (L1 or L2 / L3 ) -55 V |
| Controlling a digital input |
Yes |
| Switching capacity of the outputs |
| Lamp load, max. |
5 W |
| Load resistance range |
| lower limit |
41 Ω |
| upper limit |
28000 Ω |
| Output voltage |
| Rated value (DC) |
24 V |
| for signal "1", min. |
Ua - 3 V |
| Output current |
| for signal "1" rated value |
0.5 A |
| for signal "1" permissible range for 0 to 60 °C, max. |
0.5 A |
| Output delay with resistive load |
| "0" to "1", max. |
50 ms |
| "1" to "0", max. |
200 ms |
| Parallel switching of 2 outputs |
| for increased power |
No |
| for redundant control of a load |
Yes; only outputs of the same group |
| Switching frequency |
| with resistive load, max. |
100 Hz |
| with inductive load, max. |
0.5 Hz |
| on lamp load, max. |
8 Hz |
| Aggregate current of outputs (per group) |
| all mounting positions |
| up to 60 °C, max. |
4 A |
| horizontal installation |
| up to 40 °C, max. |
3000 mA |
| up to 60 °C, max. |
2000 mA |
| all other mounting positions |
| up to 40 °C, max. |
2 A |
| Cable length |
| Cable length, shielded, max. |
1000 m |
| Cable length unshielded, max. |
600 m |
| Interfaces |
| PROFIBUS DP |
| Transmission rate, max. |
1.5 Mbit/s |
| Direct data exchange (slave-to-slave communication) |
Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC) |
| Communication functions |
| Bus protocol/transmission protocol |
PROFIBUS DP |
| Interrupts/diagnostics/status information |
| Alarms |
| Alarms |
No |
| Diagnostic messages |
| Diagnostic functions |
Yes |
| Diagnostics indication LED |
| Bus fault BF (red) |
Yes |
| Status indicator digital output (green) |
Yes |
| Status indicator digital input (green) |
Yes |
| Monitoring 24 V voltage supply ON (green) |
Yes |
| Galvanic isolation |
| between PROFIBUS DP and all other circuit components |
Yes |
| Galvanic isolation digital outputs |
| between the channels |
No |
| between the channels and PROFIBUS DP |
Yes; Optocoupler |
| Isolation |
| Isolation checked with |
500 V DC |
| Degree and class of protection |
| IP20 |
Yes |
| Ambient conditions |
| Operating temperature |
| horizontal installation, min. |
0 °C |
| horizontal installation, max. |
60 °C; 40°C for other mountings |
| Air pressure |
| permissible range, min. |
795 hPa |
| permissible range, max. |
1080 hPa |
| Relative humidity |
| Operation, min. |
5 % |
| Operation, max. |
95 %; RH class 2 in accordance with IEC 1131-2 |
| Vibrations |
| Operation, checked according to IEC 60068-2-6 |
Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g) |
| Shock test |
| checked according to IEC 60068-2-27 |
Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms |
| Connection method |
| Inputs/outputs |
Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection |
| Dimensions |
| Width |
145 mm |
| Height |
60 mm |
| Depth |
60.5 mm |
| Weights |
| Weight, approx. |
130 g |
| Status |
Feb 10, 2014 |
